Shop for American DJ V Power Amplifier and more at everyday discount prices with free shipping over $50* on – Your Online Store!. Buy the ADJ V Amplifier at PlanetDJ. Low VIP Pricing, Financing and Free Shipping available. American Audio | V | User manual | American Audio V User manual American Audio® – – V Vplus Series Amplifiers Power.

Author: Tobei Makus
Country: Kosovo
Language: English (Spanish)
Genre: Education
Published (Last): 25 November 2017
Pages: 193
PDF File Size: 11.94 Mb
ePub File Size: 12.55 Mb
ISBN: 598-1-96575-517-3
Downloads: 4214
Price: Free* [*Free Regsitration Required]
Uploader: Talrajas

When the input signal decreases enough that clipping ends, the limiter will deactivate and cease its gain reduction.

American DJ V3000 2 Channel Professional Stereo Amplifier

The appliance has been exposed to rain amerian water. The XLR jack is configured as follows; Pin three positive, pin two negative, pin one ground. The speaker wire may be connect by bare wire directly connected, usually for permanent connectionsbanana plug, or spade connector.

The front panel provides four holes used to screw the unit into a rack. No hay piezas adentro que el usario puede reparar.

The amplifier can operate at practically any power level without risk of overheating. Turn your input source level up.

V Power Amplifier by American Audio Valuation Report by

It will allow brief clipping of peaks and will only activate when continuous, hard clipping occurs. During signal overload, the limiter will reduce the input audio signal enough a,erican minimize the amount of clipping.

During excessive clipping the limiter will reduce the audio signal enough to minimize the amount of clipping. Turning the knob in a clockwise direction will increase signal output.

American Audio V3000/V2000 Stereo Amplifier User Manual

If it is lit about half the time, the amplifier channel will probably go into thermal protection within a few ej. Ensuring proper polarity will avoid speakers being out of phase, that can cause a loss of bass response. Always use the 50 Hz filter setting if you are using the amplifier to drive a distributed line system also known as a constant-voltage line, 70 volt line, etc.

  CONCEPTS IN BIOLOGY ENGER 14TH EDITION PDF

Insert the bare wire into the hole that was reveled by unscrewing the binding post cap. At this point channel one will begin to distort. This may reduce the buzz that is caused aamerican an electrical 60Hz cycle.

American Audio › V › Amplifier – Gearbase | DJResource

Insert the spade connector in to the binding post and tighten the caps down on the spade connector. Banana Plugs – When connecting your speakers to the amplifier using banana jacks; Be sure that the red and black caps on the binding post are completely screwed in.

See limiter page Vor Inbetriebnahme unbedingt die Bedienungsanleitung lesen. The fixture does not appear to operate normally or exhibits a marked change in performance. The dip switches on the rear panel allows you to enable or disable the filter for each channel, as well as adjust either a 50Hz or 30 Hz cut-off.

A short circuit will usually be traced to a bad cable or a bad speaker component and is rarely traced to the amplifier itself. Bridged-Mono Mode Caution – The voltage across the output terminals of a bridged V Vplus series amplifier may equal or exceed volts RMS and may be as high as volts.

Use your front gain controls to regulate the output volume. Never block the fan in any way or mount in an enclose rack, doing so may cause the amplifier to overheat and fail. Fuse Holder – 10 5 11 6 12 1 Diagram 3 This holder houses the external fuse. Fuse Holder – This holder houses the external fuse. The power-supply cord or the plug has been damaged. Connect your speaker across the red output binding post on the rear of your amplifier.

  HIDANTAL INJETAVEL BULA PDF

Turn channel two gain up. Amplifiers arrive to you preset in the stereo operation mode. During normal operation below clipping, and momentary clips on peaks, the limiter does not affect the audio signal and is inaudible. When constructing your own XLR cables follow the pin configuration describe below for proper connections. When connecting your speakers to the amplifier using banana jacks; Be sure that the red and black caps on the binding post are tighten down completely.

Dieses Symobl soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen, die Handhabung und Wartung des Produkts betreffen. Each channel operates independently of each other allowing each channel to have different filter settings. Never plug your amplifier in to a wall outlet that does not match the required voltage of your amplifier, serious damage may occur to your unit. Always be sure the source voltage for your areas matches the required voltage for your amplifier.

To reduce the risk of shock or damage to your amplifier, be sure that the wire connected to one binding post does not come in contact with that of another. The diagram below detail the functions of each dip switch, the functions are also printed on the rear panel of the amplifier. Typical speaker output using bare wire.

The dip switches on the rear panel allows you to configure the low cut filter. Use the channel one gain to regulate your amplifier output. When the channel goes into protect mode all output for that channel will turn off.