ASTM D – Designation: D – 06 Standard Practice for Plastics: Dynamic Mechanical P. ASTM D Standard Practice for Plastics: Dynamic Mechanical Properties: Determination and Report of Procedures. standard by ASTM. dpdf – Download as PDF File .pdf), Text File .txt) or read online. This practice is under the jurisdiction of ASTM Committee D20 on Plastics and.

Author: Brazshura Fedal
Country: Kenya
Language: English (Spanish)
Genre: Finance
Published (Last): 21 May 2009
Pages: 113
PDF File Size: 10.28 Mb
ePub File Size: 14.91 Mb
ISBN: 478-8-21285-156-6
Downloads: 33440
Price: Free* [*Free Regsitration Required]
Uploader: Kigasho

ASTM G39 – 99 D — 06 Standard Practice for Plastics: Determination and Report of Procedures 1 This standard is issued under the xed designation D ; the number immediately following the designation indicates the year of original adoption asfm, in the case of revision, the year of last revision.

A number in parentheses indicates the year of last reapproval. A superscript epsilon e indicates an editorial change since the last revision or reapproval.

This standard has been approved for use d40665 agencies of the Department of Defense. It incorporates laboratory practice for determining dynamic mechanical properties of plastic specimens subjected to various oscillatory deformations on a variety of instruments of the type commonly called dynamic mechanical analyzers or dynamic thermomechanical analyzers. Plots of elastic and dd4065 moduli are indicative of the viscoelastic characteristics of a plastic.

These moduli are functions of temperature or frequency in plastics, and change rapidly at particular temperatures or frequencies. The regions of rapid moduli change are normally referred to as transition regions. Without changing the observed data, reporting in full as described in this practice the conditions under which the data were obtained will enable apparent differences observed in another study to be reconciled.

An assumption of this technique is that testing is conducted in the region of linear viscoelastic behavior. The values given in brackets are for information only. It is the responsibility of the user of this practice to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Specic hazards statements are given in Section 8. Current edition approved Dec. Originally approved in Last previous edition approved in as D – Summary of Practice 4.


Elastic or loss moduli, or both of the specimen are measured while varying time, temperature of the specimen or frequency of the oscillation, or both the latter. Plots of the elastic or loss moduli, or both, are indicative of viscoelastic characteristics of the specimen.

Rapid changes in viscoelastic properties at particular temperatures, times, or frequencies are normally referred to as transition regions. NOTE 2—The particular method for measurement of elastic and loss moduli depends upon the operating principle of the instrument used.

Dynamic Mechanical Analysis ASTM D4065, D4440, D5279

Therefore, consult the appropriate material specication before using this practice. Instruments of this type are commonly called dynamic mechanical or dynamic thermomechanical analyzers. They typically operate in one of seven oscillatory modes: The deformation strain shall be applied and then released, as in free-vibration devices, dd4065 continuously applied, as in forcedvibration devices see Table 1.

Any temperature programmer should be sufficiently stable to permit measurement of sample temperature to Signicance and Use 5. A plot of the elastic modulus and loss modulus of material versus temperature provides a graphical representation of elasticity and damping as a function of temperature or frequency. In the temperature ranges where signicant changes occur, elastic modulus decreases rapidly with increasing temperature at constant or near constant frequency or increases with increasing frequency at constant temperature.

ASTM D4065 Plastic Dynamic Mechanical Properties | Testing Machine

A maximum is observed for the loss modulus, as well as for the tan delta curve, in the transition region. If some heat treatment is applied to the specimen to obtain this preferred analytical form, this treatment shall be noted in the report. In many cases, a specimen of 0. NOTE 3—It is important to select a specimen size consistent with the modulus of the material under test and capabilities of the measuring apparatus.

For example, while thick specimens of low modulus materials are suitable for measurement, thin specimens of high modulus materials are required. Dfor those tests where conditioning is required. If other specimen conditioning is used, it should be noted in the report. Refer to EEand E for additional details on calibration.

Mechanical spectrometerB,C Sinusoidal xed or variable frequency Forced constant amplitude; atsm or variable frequency-torsional oscillation see Fig.


C Instruments of this type are available from Rheometric-Scientic, Inc. NOTE 4—Preferably, tests conducted over a temperature range should be performed in incremental steps or at a rate slow enough to allow temperature equilibrium throughout the d465 specimen. The time to reach equilibrium will depend upon the mass of the particular specimen and the gripping arrangement.

ASTM D Plastic Dynamic Mechanical Properties | Testing Machine

The d40655 of heating rate is observed by running specimens at two or more rates and comparing the elastic and viscous property results obtained. NOTE 5—The accuracy required of the temperature measurement will depend upon the rate of change of moduli with temperature of the plastic being investigated. In transition regions, experience has indicated that the specimen temperature should be read to Clearly label the abscissa with title and units of measurement.

D — 06 The abscissa should be clearly labeled with title and units of measurement. December 1, 1 Editorial revisions made throughout. ASTM International takes no position respecting the validity of v4065 patent rights asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed asttm ve years and if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.

If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below.

Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.